How Thick Should Bookshelves Be

How thick should plywood be for shelves?

The most common size used in shelving is a 3/4 inch thickness. Cabinetry, furniture, and smaller decorative projects might generally use a combination of 1/2 and 3/4 and occasionally 1/4 inch.

Are 2x2 strong enough for shelves?

Using 2-by-2-inch pieces of lumber to create a shelf can give you a rustic-style piece of decor that is not only incredibly durable but also easy on the wallet and the eyes.

How deep should built in book shelves be?

Most shelves are built a minimum of 11 to 12 inches deep, but this is your chance to customize: Go for it!

Is 12mm plywood OK for shelves?

12mm Hardwood Plywood is the perfect thickness for modular shelving too - it's lightweight but not too clunky - which is ideal if you're looking to make contemporary hexagonal shelving like the picture below.

Is OSB board better than plywood?

Osb is stronger than plywood in shear. Shear values, through its thickness, are about 2 times greater than plywood. This is one of the reasons osb is used for webs of wooden I-joists. However, nail-holding ability controls performance in shear wall applications.

What is a good shelf depth?

The shelves shouldn't be too deep.

The standard depth of most shelves is 16 to 20 inches deep. The highest shelf should be shallower, like 12 inches deep, to make those items easier to access. If you find that stuff seems to get pushed to the back and forgotten about, you should consider even shallower shelves.

How deep should a wall shelf be?

As far as shelf size, a depth of 10 or 12 inches fits most functions without concern of drooping in the middle, while length should be determined based on where you want to install yours. If you want a long span but are concerned about weight, install adjacent, identical floating shelves, or opt for bracket supports.

Can you use 2x3 for shelves?

I specifically chose 2x3 studs because they're plenty strong for this kind of shelving unit, while being a little less expensive than regular 2x4 studs, and a little lighter and easier to build. You can use plywood instead of OSB, but you'll spend more on the shelves.

Can I use 2x3 for shelving?

If you want to affix the shelves directly to the wall, try the following trick: attach the 2x3 for the shelf to the wall first! Be sure of your location, and check for level. When you build that shelf, leave out the 2x3 that is on the wall. If the wall is uneven, your shelving will be, too!!

How much weight will a 2x3 hold?

Registered. Assuming you would be spanning the 6 ft direction, a 2x3 will safely carry about 70 lbs (point load at the center).

Is MDF good for bookcases?

MDF is commonly used for shelving in closets and cabinets because it's inexpensive and smooth. But MDF isn't as stiff as plywood and will sag over time. So when I use MDF shelving for heavy loads, I simply beef it up with wood.

Is MDF stronger than chipboard?

Medium density fibreboard is stronger than chipboard because the board has a higher density. Medium density fibreboard also has a much smoother surface than particle board which allows for a better finish. Kitchen - MDF outperforms chipboard because it is water resistant.

Is MDF stronger than plywood?

MDF is ideal for cutting, machining and drilling, since it does not chip easily. On the other hand, plywood is a much more stronger material, which can be used for doors, floors, staircases and outdoor furniture.

Can you use 1/2 plywood shelves?

They cost more than plywood, but I think ease of use and durability make it worth it. Adding 1x2s under the plywood will stiffen it up just fine. Use glue and finishing nails, nailed from the top, into the 1x part of the sticks to make a shelf section.

Will plywood shelves sag?

A 30” wide adjustable shelf that is 10” deep, made of any of these three (plywood, poplar, pine) materials, will have an acceptable sag for a load of up to 35# per foot, or about 90# for the entire shelf. Sag definitely won't be a problem for those small adjustable shelves.

Can I use chipboard for shelves?

Chipboard. Plain chipboard - unlaminated chipboard is the cheapest and weakest material. It is generally unsuitable for shelving as the finish is poor. Laminated chipboard - laminated chipboard is cheaper than solid timber and comes in a number of different types of veneer.

Do screws hold better in OSB or plywood?

Plywood and OSB: Screw withdrawal or holding ability. Group 1 plywood, made from the strongest species of wood such as Southern Yellow Pine, holds screws better than OSB.

Can I use 7/16 OSB for wall sheathing?

Fred S. The 24/16 rating of 7/16" OSB will pass code for any standard construction (walls &roof). You don't need to worry about that. That is the job of the contractor and inspector.

Which is cheaper plywood or OSB?

OSB is less expensive than plywood. To build a typical 2,400-square foot home, OSB may cost $700 less than plywood. OSB is considered by many to be a “green” building material because it can be made from smaller-diameter trees, such as poplars, that are often farmed.

What is the average pantry size?

The average pantry dimensions are 5 feet by 5 feet, but this varies depending on the size of your home and the amount of storage you are aiming for. There should be a minimum aisle width of 44 inches to easily move around the pantry.

What is the standard shelf depth?

With most book widths of around 4.25 inches to 8 inches, the standard bookshelf depth is between 10 to 12 inches. But you can find bookshelves on the market with a depth ranging from 7 to 15 inches.

How deep should open shelving be in kitchen?

Open shelving in a kitchen should be deep enough to hold a stack of dinner plates which are typically 12″ deep. This is also the perfect minimum depth for displaying cookbooks.

How thick are floating shelves?

I love the look of floating built-in shelves, but most tutorials have shelves that look very bulky and are at least 3 inches thick.

What is 2x3 lumber used for?

Great lumber, these can be used for studs, shelving, fence backer rails or any project where you need strength but with a little less strength, cost and size compared to a 2 x 4.

How do you build a 2x3 shelf?

How do you build shelves with 2x4 and plywood?

Which is stronger 2 2x4 or 1 2x6?

Bearing capacity is a function of the footprint area of all the studs in a wall. The total bearing area of three 2x4s is 15 3/4 square inches; two 2x6s have a bearing area of 16 square inches. In bending, however, such as from a wind load, a 2x6 wall is considerably stronger.

Can you build a shed out of 2x3?

Registered. Single 2x3 studs at 12" or 16" are fine for a shed with wall heights at least up to 8'; at that height, it might get some flexing in strong winds - I wouldn't try to drywall it.

What span can a 2x4 support?

According to the American Wood Council, Douglas Fir 2x4s spaced 24 inches apart can handle a maximum span of 6 feet 6 inches. In comparison, Sitka Spruce is slightly stronger with a maximum span of 6 feet 8 inches.

How wide can a bookshelf be without sagging?

Bookshelf width is typically no more than 12 inches. Bookcase shelves using 3/4-inch plywood or hardwood solids with braces spaced no farther apart than 36 inches will not sag.

What does MDF stand for?

MDF is an abbreviation for Medium Density Fiberboard. People tend to look down on MDF and automatically assume solid wood is the better choice.

Leave a Comment

Your email address will not be published.