How far should a stove pipe be from the wall?
An unprotected stove pipe should be at least 18 inches from an unprotected wall or ceiling.
How far does a wood stove need to be away from a tiled wall?
If no wall protection is used, the common radiant-type stove or heater must be spaced out at least 36 inches from the wall. This distance may be reduced considerably if asbestos millboard and/or 28 gage sheet metal is used for wall protection.
Can you put a wood burning stove against a wall?
Yes. If a UL-listed stove has a heat shield attached, the clearance can be reduced as specified. Or build a heat shield to be mounted 1 inch off the wall on non-combustible spacers.
The pipe should be as straight and short as possible, with sections properly secured. The horizontal portion of the pipe should rise not less than one-quarter inch to the linear foot, to insure a good draft. You should not pass a stove pipe through a combustible wall for a hook-up with a chimney flue.
A combustible floor must be protected by a non-combustible material (like tile, concrete board, or certified to UL-1618 or as defined by local codes) extending beneath the heater and a minimum of 6" from each side and minimum 16" from the front face of the stove and minimum 6" (or the rear clearance to combustibles
Brick and stone are a common materials to use behind a wood stove, while many stoves can be purchased with optional heat shields to help reduce clearances.
Non-combustible materials are building materials that do not burn or ignite when subjected to expected levels of fire or heat. Examples of non-combustible materials include brick masonry, concrete blocks, hardy backer board, calcium silicate board, cement board, metal, and certain types of glass.
Inside the enclosure, building codes require a 2-inch clearance around the double- or triple-wall chimney pipe. While a double-wall class A chimney pipe is adequate for most installations, wood stoves installed in mobile homes are required to use a triple-wall chimney pipe.
Wood stoves require heat shields both under and behind them to protect your home from heat damage. While many wood stoves include heat shields in their design, some do not. Shields protect your home from heat damage and fire one of two ways.
Concrete backer board, which is a tile underlayment, provides a heat-resistant, rigid foundation. Most sheets are 3 feet wide and 5 feet long, which isn't large enough to provide adequate protection for some stoves. Using two sheets side-by-side covers more space.
How much space do you need on each side of a stove? The amount of space you'll want to have on either side of this appliance will vary according to how much you'll be using it. It's recommended to have a minimum of fifteen to eighteen inches on both sides.
So, for a 30-inch stove, you need to have a 31-inch gap. This will allow for a half-inch space between the stove and your cabinets. The same applies to larger stoves, try to keep a half-inch on either side of the stove.
How much space should be provided in front of a kitchen stove? A minimum clearance 'work zone' of 40” (102 cm) should be provided in front of a kitchen stove, with a larger 48”-60” (122-152 cm) clearance provided between other kitchen appliances.
Maximum unsupported horizontal length: 1 m (3 feet). Galvanized flue pipes must not be used because the coatings vaporize at high temperatures and release dangerous gases.
Plate steel stoves need firebrick. The cast iron stoves usually don't. If your stove came from the factory with brick, rebrick it.
There is a risk of carbon monoxide poisoning when you sleep in a room where a conventional coal or gas fire, a log burner, a cooker, or a back burner is left on overnight. You cannot feel the early symptoms of carbon monoxide poisoning, so it is important that you protect yourself.
Hardi cement board is an inexpensive solution that will form the foundation of an effective heat shield for any application. Hardi cement board is also designed to have ceramic, porcelain or stone tiles installed over it to cover and beautify the heat shield after it is installed.
Strong, durable and resistant to water damage, DUROCK® Next Gen Cement Board is ideal for use in partitions, walls, floors and ceilings in residential construction and can be used as a heat shield. Water, Mould and Moisture Resistant.
Hardiebacker is a brand name for a line of fiber cement boards used in construction projects. This material has strong moisture-resistance capabilities and is also heat resistant, making it an ideal liner for projects around your fireplace.
Drywall is combustible and not a suitable material either for use behind the wood stove or for use underneath tile. Removing it from the wall behind the wood stove allows you to install cement backerboard instead. Cut right through the drywall using a drywall saw.
Each model is assessed differently and you need to refer to the manufacturers instruction. However, the standard wood heater distance from the rear wall is around 300mm and the side walls 500mm.
Gypsum board, because of its combustible facing, will not pass ASTM E136. Therefore remember, under the Mechanical Subcode, gypsum wallboard is classified as a combustible material.
Yes, HardieBacker® 1/4" Cement Board is deemed noncombustible when tested to ASTM E 136 and can be used in conjunction with other noncombustible materials around a fireplace.
No, you cannot use single wall stove pipe outside. It'll lose its integrity over time, and will not keep the gases hot enough to prevent the toxic creosote buildup. Without the insulating layer, it will cause cold hearth syndrome, and force the smoke back into your home. You need a Class-A chimney to vent outside.
Stove pipe is uninsulated pipe used in the room where the stove or other appliance is located. Stove pipe is made in single- and double-wall versions. Chimney pipe also is made in two types, double wall and triple wall.
The top of a chimney pipe must extend at least 2 feet above the peak of the roof, if the pipe is within 10 feet of the peak. If the pipe is farther than 10 feet from the roof peak, it must be 2 feet above the highest point of the roof within 10 feet.
All Answers (7) aluminum is the perfect heat shield material offering excellent protection against excessive exhaust system heat. Ultra-high-temperature ceramics,(UHTC), such as zirconium diboride (ZrB2) and hafnium diboride (HfB2) may be of choice.
Installing a TV directly above a wood stove isn't typically recommended, but if a TV will be sufficiently protected from the heat of a wood stove it may be suitable. TVs should be placed outside of clearance distances to combustibles, and a mantel can help protect a TV from the heat.
ANSWER - Ceramic tile behind a woodstove works very well as long as it's installed correctly over the right type of substrate. It's important, though, that the tile is attached to a surface that's not affected by heat. It's best to use a concrete substrate like a mortar bed or a cementitious backer unit.
There is no legal requirement or stove building regulation that states that you to have a flue liner in your chimney if it is in good condition. However, they are strongly advised by most HETAS installers for both safety and performance reasons. Some of these are: Improved draw.
Keep in mind that your wood-burning fireplace, however, definitely should have a hearth. A hearth helps protect your home from errant sparks that could turn an evening of roasting chestnuts into a traumatizing visit from the fire department.
Ovens must have a minimum of 15 inches of adjacent landing area on either side. However, because most ovens tend to be located under stoves as part of a single appliance, this landing area is usually already covered under the stove requirements.
Use a silicone material if there is any height difference between your stovetop and the counter. Silicone is more flexible and will fit the form better. Use stainless steel gap covers to match a metal stove-top seamlessly.
Venting is an important component of all stoves. And wood, gas, and pellet stoves have different venting systems. For instance, wood-burning stoves will always be vented through the roof of your house, but pellet-burning stoves can be vented vertically through the roof, or horizontally through the wall to the outdoors.
As excessive bends and horizontal runs can accumulate soot with the risk of blockage, the flue pipe should be kept as vertical as possible and the angle of bends should be no more than 45° from the vertical.